Difference between revisions of "StarlingX/Installation Guide"
(→Bare Metal) |
(→Bare Metal) |
||
Line 18: | Line 18: | ||
* '''Controller Hosts''' | * '''Controller Hosts''' | ||
− | |||
− | |||
** Minimum Processor is: | ** Minimum Processor is: | ||
*** Dual-CPU Intel® Xeon® E5 26xx Family (SandyBridge) 8 cores/socket | *** Dual-CPU Intel® Xeon® E5 26xx Family (SandyBridge) 8 cores/socket | ||
** Minimum Memory: 64 GB | ** Minimum Memory: 64 GB | ||
+ | ** Hard Drives | ||
+ | *** Primary Hard Drive, minimum 500 GB for OS and system databases. | ||
+ | *** Secondary Hard Drive, minimum 500 GB for persistent VM storage. | ||
** Two physical Ethernet interfaces | ** Two physical Ethernet interfaces | ||
** USB boot support | ** USB boot support | ||
** PXE boot support | ** PXE boot support | ||
* '''Storage Hosts''' | * '''Storage Hosts''' | ||
− | |||
− | |||
** Minimum Processor is: | ** Minimum Processor is: | ||
*** Dual-CPU Intel® Xeon® E5 26xx Family (SandyBridge) 8 cores/socket | *** Dual-CPU Intel® Xeon® E5 26xx Family (SandyBridge) 8 cores/socket | ||
** Minimum Memory: 64 GB | ** Minimum Memory: 64 GB | ||
+ | ** Hard Drives | ||
+ | *** Primary Hard Drive, minimum 500 GB for OS. | ||
+ | *** 1 or more additional Hard Drives for CEPH OSD storage, and | ||
+ | *** Optionally 1 or more SSD or NVMe Drives for CEPH Journals. | ||
** Three physical Ethernet interfaces | ** Three physical Ethernet interfaces | ||
** PXE boot support | ** PXE boot support |
Revision as of 15:38, 5 October 2018
Intro
StarlingX may be installed in:
- Bare Metal: Real deployments of StarlingX are only supported on physical servers.
- Virtual Environment: It should only be used for evaluation or development purposes.
StarlingX installed in virtual environments has two options:
- Libvirt/QEMU
- VirtualBox
Requirements
Different use cases require different configurations.
Bare Metal
The minimum requirements for the physical servers where StarlingX might be deployed, include:
- Controller Hosts
- Minimum Processor is:
- Dual-CPU Intel® Xeon® E5 26xx Family (SandyBridge) 8 cores/socket
- Minimum Memory: 64 GB
- Hard Drives
- Primary Hard Drive, minimum 500 GB for OS and system databases.
- Secondary Hard Drive, minimum 500 GB for persistent VM storage.
- Two physical Ethernet interfaces
- USB boot support
- PXE boot support
- Minimum Processor is:
- Storage Hosts
- Minimum Processor is:
- Dual-CPU Intel® Xeon® E5 26xx Family (SandyBridge) 8 cores/socket
- Minimum Memory: 64 GB
- Hard Drives
- Primary Hard Drive, minimum 500 GB for OS.
- 1 or more additional Hard Drives for CEPH OSD storage, and
- Optionally 1 or more SSD or NVMe Drives for CEPH Journals.
- Three physical Ethernet interfaces
- PXE boot support
- Minimum Processor is:
- Compute Hosts
- Primary Hard Drive, minimum 500 GB for OS and system databases.
- Secondary Hard Drive, minimum 500 GB for persistent VM storage.
- Minimum Processor, Dual-CPU Intel® Xeon®
- Minimum Memory: 32 GB
- Three physical Ethernet interfaces
- PXE boot support
The recommended minimum requirements for the physical servers are described later in each StarlingX Deployment Options guide.
Virtual Environment
The recommended minimum requirements for the workstation, running the Virtual Machine(s) where StarlingX will be deployed, include:
Hardware Requirements
A workstation computer with:
- Processor: x86_64 only supported architecture with BIOS enabled hardware virtualization extensions
- Cores: 8 (4 with careful monitoring of cpu load)
- Memory: At least 32GB RAM
- Hard Disk: 500GB HDD
- Network: Two network adapters with active Internet connection
Software Requirements
A workstation computer with:
- Operating System: Freshly installed Ubuntu 16.04 LTS 64-bit
- Proxy settings configured (if applies)
- Git
- KVM/VirtManager
- Libvirt Library
- QEMU Full System Emulation Binaries
- <stx-deployment> project
- StarlingX ISO Image
Deployment Environment Setup
This section describes how to set up a StarlingX system in a workstation computer. After completing these steps, you will be able to deploy and run your StarlingX system on the following Linux distribution:
- Ubuntu 16.04 LTS 64-bit
Updating Your Operating System
Before proceeding with the build, ensure your OS is up to date. You’ll first need to update the local database list of available packages:
$ sudo apt-get update
Install stx-tools project
Clone the stx-tools project. Usually you’ll want to clone it under your user’s home directory.
$ cd $HOME $ git clone git://git.openstack.org/openstack/stx-tools
Installing Requirements and Dependencies
Navigate to the stx-tools installation libvirt directory:
$ cd $HOME/stx-tools/deployment/libvirt/
Install the required packages:
$ bash install_packages.sh
Disabling Firewall
Unload firewall and disable firewall on boot:
$ sudo ufw disable Firewall stopped and disabled on system startup $ sudo ufw status Status: inactive
Getting the StarlingX ISO Image
Follow the instructions from StarlingX/Developer_Guide to build a StarlingX ISO image.
Bare Metal
A bootable USB flash drive containing StarlingX ISO image.
Virtual Environment
Copy the StarlingX ISO Image to the <stx-deployment> libvirt project directory:
$ cp <starlingx iso image> $HOME/stx-tools/deployment/libvirt/
Deployment Options
- Standard Controller
- All-in-one