|
|
| (19 intermediate revisions by 9 users not shown) |
| Line 1: |
Line 1: |
| − | = Installing StarlingX with containers: All in One Duplex configuration = | + | {{Warning|header='''Warning - Deprecated'''|body='''This wiki page is out of date and now deprecated. For the current and upcoming versions, see [https://docs.starlingx.io/deploy_install_guides/index.html StarlingX Installation and Deployment guides]'''}} |
| | | | |
| − | == History == | + | = Documentation Contribution = |
| | | | |
| − | * '''January 24, 2019:''' Initial draft
| + | You might consider contributing to StarlingX documentation if you find a bug or have a suggestions for improvement. |
| − | * '''January 28, 2019:''' Configure datanetworks in sysinv, prior to referencing it in the 'system host-if-modify/host-if-add command'. Needed on loads Jan 25, 2019 or later.
| + | To get started: |
| − | * '''January 29, 2019:''' Removed obsolete neutron host/interface configuration and updated DNS instructions.
| |
| | | | |
| − | == Introduction == | + | * Please use "[https://docs.starlingx.io/contributor/index.html Contribute]" guides. |
| | + | * Launch a bug in [https://bugs.launchpad.net/starlingx/+bugs?field.tag=stx.docs StarlingX Launchpad] with the tag ''stx.docs''. |
| | | | |
| − | These instructions are for an All-in-one duplex system (AIO-DX) in VirtualBox. Other configurations are in development.
| + | = History = |
| | | | |
| − | Installing on bare metal is also possible, however the the process would have to be adapted for the specific hardware configuration.
| + | Go to [https://wiki.openstack.org/w/index.php?title=StarlingX/Containers/InstallationOnAIODX&action=history Page > History] link if you want to: |
| | | | |
| − | '''Note''': These instructions are valid for a load built on '''January 25, 2019''' or later.
| + | * See the old content of this page |
| − | | + | * Compare revisions |
| − | == Building the Software ==
| |
| − | | |
| − | Refer to these instructions on the AIO SX page [[StarlingX/Containers/Installation#Building_the_Software| Building the Software]]
| |
| − | | |
| − | == Setup the VirtualBox VM ==
| |
| − | | |
| − | Refer to these instructions on the AIO SX page [[StarlingX/Containers/Installation#Setup_the_VirtualBox_VM| Setup the VirtualBox VM]]
| |
| − | | |
| − | Remember to setup TWO VMs.
| |
| − | | |
| − | === VirtualBox Nat Networking ===
| |
| − | | |
| − | Refer to these instructions on the AIO SX page [[StarlingX/Containers/Installation#VirtualBox_Nat_Networking| VirtualBox Nat Networking]]
| |
| − | | |
| − | == Setup Controller-0 ==
| |
| − | === Install StarlingX ===
| |
| − | | |
| − | Boot the VM from the ISO media. Select the following options for installation:
| |
| − | *All-in-one Controller
| |
| − | *Graphical Console | |
| − | *Standard Security Profile
| |
| − | | |
| − | Once booted, log into Controller-0 as user wrsroot, with password wrsroot. The first time you log in as wrsroot, you are required to change your password. Enter the current password (wrsroot):
| |
| − | | |
| − | <pre>
| |
| − | Changing password for wrsroot.
| |
| − | (current) UNIX Password: wrsroot
| |
| − | </pre>
| |
| − | | |
| − | Enter a new password for the wrsroot account and confirm it.
| |
| − | | |
| − | === Run config_controller ===
| |
| − | | |
| − | <code>sudo config_controller --kubernetes</code>
| |
| − | | |
| − | Use default settings during config_controller, except for the following:
| |
| − | * System mode: '''duplex'''
| |
| − | * If you do not have direct access to the google DNS nameserver(s) 8.8.8.8 , 8.8.4.4 you will need to configure that when prompted. Press Enter to choose the default, or type a new entry.
| |
| − | * If you do not have direct access to the public docker registry (https://hub.docker.com/u/starlingx) and instead use a proxy for internet access, you will need to add proxy information when prompted. (Storyboard 2004710 was merged on Jan 30, 2019. )
| |
| − | | |
| − | After you apply the configuration
| |
| − | <pre>
| |
| − | The following configuration will be applied:
| |
| − | | |
| − | System Configuration
| |
| − | --------------------
| |
| − | Time Zone: UTC
| |
| − | System mode: duplex
| |
| − | | |
| − | PXEBoot Network Configuration
| |
| − | -----------------------------
| |
| − | Separate PXEBoot network not configured
| |
| − | PXEBoot Controller floating hostname: pxecontroller
| |
| − | | |
| − | Management Network Configuration
| |
| − | --------------------------------
| |
| − | Management interface name: enp0s8
| |
| − | Management interface: enp0s8
| |
| − | Management interface MTU: 1500
| |
| − | Management subnet: 192.168.204.0/24
| |
| − | Controller floating address: 192.168.204.2
| |
| − | Controller 0 address: 192.168.204.3
| |
| − | Controller 1 address: 192.168.204.4
| |
| − | NFS Management Address 1: 192.168.204.5
| |
| − | NFS Management Address 2: 192.168.204.6
| |
| − | Controller floating hostname: controller
| |
| − | Controller hostname prefix: controller-
| |
| − | OAM Controller floating hostname: oamcontroller
| |
| − | Dynamic IP address allocation is selected
| |
| − | Management multicast subnet: 239.1.1.0/28
| |
| − | | |
| − | Infrastructure Network Configuration
| |
| − | ------------------------------------
| |
| − | Infrastructure interface not configured
| |
| − | | |
| − | Kubernetes Cluster Network Configuration
| |
| − | ----------------------------------------
| |
| − | Cluster pod network subnet: 172.16.0.0/16
| |
| − | Cluster service network subnet: 10.96.0.0/12
| |
| − | Cluster host interface name: enp0s8
| |
| − | Cluster host interface: enp0s8
| |
| − | Cluster host interface MTU: 1500
| |
| − | Cluster host subnet: 192.168.206.0/24
| |
| − | | |
| − | External OAM Network Configuration
| |
| − | ----------------------------------
| |
| − | External OAM interface name: enp0s3
| |
| − | External OAM interface: enp0s3
| |
| − | External OAM interface MTU: 1500
| |
| − | External OAM subnet: 10.10.10.0/24
| |
| − | External OAM gateway address: 10.10.10.1
| |
| − | External OAM floating address: 10.10.10.2
| |
| − | External OAM 0 address: 10.10.10.3
| |
| − | External OAM 1 address: 10.10.10.4
| |
| − | | |
| − | DNS Configuration
| |
| − | -----------------
| |
| − | Nameserver 1: 8.8.8.8
| |
| − | Nameserver 2: 8.8.4.4
| |
| − | | |
| − | Apply the above configuration? [y/n]: y
| |
| − | | |
| − | Applying configuration (this will take several minutes):
| |
| − | | |
| − | 01/08: Creating bootstrap configuration ... DONE
| |
| − | 02/08: Applying bootstrap manifest ... DONE
| |
| − | 03/08: Persisting local configuration ... DONE
| |
| − | 04/08: Populating initial system inventory ... DONE
| |
| − | 05/08: Creating system configuration ... DONE
| |
| − | 06/08: Applying controller manifest ... DONE
| |
| − | 07/08: Finalize controller configuration ... DONE
| |
| − | 08/08: Waiting for service activation ... DONE
| |
| − | | |
| − | Configuration was applied
| |
| − | | |
| − | Please complete any out of service commissioning steps with system commands and
| |
| − | unlock controller to proceed.
| |
| − | </pre>
| |
| − | | |
| − | === Provisioning the platform ===
| |
| − | | |
| − | | |
| − | ==== Set the ntp server ====
| |
| − | Refer to these instructions on the AIO SX page [[StarlingX/Containers/Installation#Set_the_ntp_server| Set the ntp server]]
| |
| − | | |
| − | ==== Configure data interfaces ====
| |
| − | Refer to these instructions on the AIO SX page [[StarlingX/Containers/Installation#Configure_data_interfaces| Configure data interfaces]]
| |
| − | | |
| − | ==== Setup partitions for Controller-0 ====
| |
| − | Refer to these instructions on the AIO SX page [[StarlingX/Containers/Installation#Setup_partitions_for_Controller-0| Setup partitions for Controller-0]]
| |
| − | | |
| − | ==== Configure Ceph for Controller-0 ====
| |
| − | Refer to these instructions on the AIO SX page [[StarlingX/Containers/Installation#Configure_Ceph_for_Controller-0| Configure Ceph for Controller-0]]
| |
| − | | |
| − | ==== Unlock Controller-0 ====
| |
| − | source /etc/platform/openrc
| |
| − | system host-unlock controller-0
| |
| − | | |
| − | == Boot the second AIO controller ==
| |
| − | | |
| − | Boot the second VM (without an ISO media mounted)
| |
| − | Hit F12 immediately when the VM starts to select a different boot option - select the "lan" option to force a network boot.
| |
| − | | |
| − | At the controller-1 console, you will see a message instructing you to configure the personality of the node. Do this from a shell on controller-0 as follows:
| |
| − | | |
| − | <pre>
| |
| − | source /etc/platform/openrc
| |
| − | system host-list
| |
| − | </pre>
| |
| − | Results indicate that ID 2 is the un-provisioned controller
| |
| − | <pre>
| |
| − | +----+--------------+-------------+----------------+-------------+--------------+
| |
| − | | id | hostname | personality | administrative | operational | availability |
| |
| − | +----+--------------+-------------+----------------+-------------+--------------+
| |
| − | | 1 | controller-0 | controller | unlocked | enabled | available |
| |
| − | | 2 | None | None | locked | disabled | offline |
| |
| − | +----+--------------+-------------+----------------+-------------+--------------+
| |
| − | </pre>
| |
| − | | |
| − | <pre>
| |
| − | system host-update 2 personality=controller
| |
| − | </pre>
| |
| − | | |
| − | The packages will install and the controller will reboot.
| |
| − | | |
| − | == Provisioning the second AIO controller ==
| |
| − | | |
| − | === Configure Data Interfaces for Controller-1 ===
| |
| − | <pre>
| |
| − | source /etc/platform/openrc
| |
| − | export COMPUTE='controller-1'
| |
| − | PHYSNET0='physnet0'
| |
| − | PHYSNET1='physnet1'
| |
| − | OAM_IF=enp0s3
| |
| − | DATA0IF=eth1000
| |
| − | DATA1IF=eth1001
| |
| − | NOWRAP="--nowrap"
| |
| − | | |
| − | echo ">>> Configuring OAM Network"
| |
| − | system host-if-modify -n oam0 -c platform --networks oam ${COMPUTE} $(system host-if-list -a $COMPUTE $NOWRAP | awk -v OAM_IF=$OAM_IF '{if ($4 == OAM_IF) { print $2;}}')
| |
| − | | |
| − | echo ">>> Configuring Cluster Host Interface"
| |
| − | system host-if-modify $COMPUTE mgmt0 --networks cluster-host
| |
| − | | |
| − | echo ">>> Configuring Data Networks"
| |
| − | SPL=/tmp/tmp-system-port-list
| |
| − | SPIL=/tmp/tmp-system-host-if-list
| |
| − | system host-port-list ${COMPUTE} $NOWRAP > ${SPL}
| |
| − | system host-if-list -a ${COMPUTE} $NOWRAP > ${SPIL}
| |
| − | DATA0PCIADDR=$(cat $SPL | grep $DATA0IF |awk '{print $8}')
| |
| − | DATA1PCIADDR=$(cat $SPL | grep $DATA1IF |awk '{print $8}')
| |
| − | DATA0PORTUUID=$(cat $SPL | grep ${DATA0PCIADDR} | awk '{print $2}')
| |
| − | DATA1PORTUUID=$(cat $SPL | grep ${DATA1PCIADDR} | awk '{print $2}')
| |
| − | DATA0PORTNAME=$(cat $SPL | grep ${DATA0PCIADDR} | awk '{print $4}')
| |
| − | DATA1PORTNAME=$(cat $SPL | grep ${DATA1PCIADDR} | awk '{print $4}')
| |
| − | DATA0IFUUID=$(cat $SPIL | awk -v DATA0PORTNAME=$DATA0PORTNAME '($12 ~ DATA0PORTNAME) {print $2}')
| |
| − | DATA1IFUUID=$(cat $SPIL | awk -v DATA1PORTNAME=$DATA1PORTNAME '($12 ~ DATA1PORTNAME) {print $2}')
| |
| − | system host-if-modify -m 1500 -n data0 -p ${PHYSNET0} -c data ${COMPUTE} ${DATA0IFUUID}
| |
| − | system host-if-modify -m 1500 -n data1 -p ${PHYSNET1} -c data ${COMPUTE} ${DATA1IFUUID}
| |
| − | </pre>
| |
| − | | |
| − | === Setup Partitions for Controller-1 ===
| |
| − | These disks are added on unlock. Using same sizes as controller-0. 34G for nova-local, 6G for cgts-vg
| |
| − | <pre>
| |
| − | source /etc/platform/openrc
| |
| − | export COMPUTE=controller-1
| |
| − | | |
| − | echo ">>> Getting root disk info"
| |
| − | ROOT_DISK=$(system host-show ${COMPUTE} | grep rootfs | awk '{print $4}')
| |
| − | ROOT_DISK_UUID=$(system host-disk-list ${COMPUTE} --nowrap | grep ${ROOT_DISK} | awk '{print $2}')
| |
| − | echo "Root disk: $ROOT_DISK, UUID: $ROOT_DISK_UUID"
| |
| − | | |
| − | echo ">>>> Configuring nova-local"
| |
| − | NOVA_SIZE=34
| |
| − | NOVA_PARTITION=$(system host-disk-partition-add -t lvm_phys_vol ${COMPUTE} ${ROOT_DISK_UUID} ${NOVA_SIZE})
| |
| − | NOVA_PARTITION_UUID=$(echo ${NOVA_PARTITION} | grep -ow "| uuid | [a-z0-9\-]* |" | awk '{print $4}')
| |
| − | system host-lvg-add ${COMPUTE} nova-local
| |
| − | system host-pv-add ${COMPUTE} nova-local ${NOVA_PARTITION_UUID}
| |
| − | | |
| − | echo ">>>> Extending cgts-vg"
| |
| − | PARTITION_SIZE=6
| |
| − | CGTS_PARTITION=$(system host-disk-partition-add -t lvm_phys_vol ${COMPUTE} ${ROOT_DISK_UUID} ${PARTITION_SIZE})
| |
| − | CGTS_PARTITION_UUID=$(echo ${CGTS_PARTITION} | grep -ow "| uuid | [a-z0-9\-]* |" | awk '{print $4}')
| |
| − | system host-pv-add ${COMPUTE} cgts-vg ${CGTS_PARTITION_UUID}
| |
| − | </pre>
| |
| − | | |
| − | === Setup Ceph for Controller-1 ===
| |
| − | <pre>
| |
| − | source /etc/platform/openrc
| |
| − | | |
| − | echo ">>> Get disk & tier info"
| |
| − | HOST="controller-1"
| |
| − | DISKS=$(system host-disk-list ${HOST})
| |
| − | TIERS=$(system storage-tier-list ceph_cluster)
| |
| − | echo "Disks:"
| |
| − | echo "$DISKS"
| |
| − | echo "Tiers:"
| |
| − | echo "$TIERS"
| |
| − | | |
| − | echo ">>> Add OSDs to primary tier"
| |
| − | system host-stor-add ${HOST} $(echo "$DISKS" | grep /dev/sdb | awk '{print $2}') --tier-uuid $(echo "$TIERS" | grep storage | awk '{print $2}')
| |
| − | | |
| − | echo ">>> system host-stor-list ${HOST}"
| |
| − | system host-stor-list ${HOST}
| |
| − | echo ">>> ceph osd tree"
| |
| − | ceph osd tree
| |
| − | </pre>
| |
| − | | |
| − | === Unlock Controller-1 ===
| |
| − | source /etc/platform/openrc
| |
| − | system host-unlock controller-1
| |
| − | | |
| − | Wait for controller-1 to reboot before proceeding.
| |
| − | | |
| − | == Prepare the hosts for running the containerized services ==
| |
| − | <pre>
| |
| − | source /etc/platform/openrc
| |
| − | | |
| − | system host-label-assign controller-0 openstack-control-plane=enabled
| |
| − | system host-label-assign controller-0 openstack-compute-node=enabled
| |
| − | system host-label-assign controller-0 openvswitch=enabled
| |
| − | | |
| − | system host-label-assign controller-1 openstack-control-plane=enabled
| |
| − | system host-label-assign controller-1 openstack-compute-node=enabled
| |
| − | system host-label-assign controller-1 openvswitch=enabled
| |
| − | | |
| − | kubectl get nodes --show-labels
| |
| − | </pre>
| |
| − | | |
| − | == Using sysinv to bring up/down the containerized services ==
| |
| − | | |
| − | === Generate the stx-openstack application tarball ===
| |
| − | Refer to these instructions on the AIO SX page [[StarlingX/Containers/Installation#Generate_the_stx-openstack_application_tarball| Generate the stx-openstack application tarball]]
| |
| − | | |
| − | === Stage application for deployment ===
| |
| − | Refer to these instructions on the AIO SX page [[StarlingX/Containers/Installation#Stage_application_for_deployment| Stage application for deployment]]
| |
| − | | |
| − | === Bring Up Services ===
| |
| − | Refer to these instructions on the AIO SX page [[StarlingX/Containers/Installation#Bring_Up_Services| Bring Up Services]]
| |
| − | | |
| − | === Verify the cluster endpoints ===
| |
| − | | |
| − | Refer to these instructions on the AIO SX page [[StarlingX/Containers/Installation#Verify_the_cluster_endpoints| here ]]
| |
| − | | |
| − | == Provider/tenant networking setup ==
| |
| − | | |
| − | Refer to these instructions on the AIO SX page [[StarlingX/Containers/Installation#Provider.2Ftenant_networking_setup| here ]]
| |
| − | | |
| − | == Additional Setup Instructions ==
| |
| − | | |
| − | Refer to these instructions on the AIO SX page [[StarlingX/Containers/Installation#Additional_Setup_Instructions| Additional Setup Instructions]]
| |
| − | | |
| − | == Horizon access ==
| |
| − | | |
| − | Refer to these instructions on the AIO SX page [[StarlingX/Containers/Installation#Horizon_access| here ]]
| |
| − | | |
| − | == Known Issues and Troubleshooting ==
| |
| − | | |
| − | None
| |
You might consider contributing to StarlingX documentation if you find a bug or have a suggestions for improvement.
To get started:
Warning - Deprecated
