Jump to: navigation, search

Difference between revisions of "Mellanox-Neutron-Train-Redhat-InfiniBand"

(Controller Node)
(Network Node)
Line 140: Line 140:
  
 
== Network Node==
 
== Network Node==
To configure the Network node:
+
# Install python-networking-mlnx package and configure DHCP and L3 agents
 +
# Install up to date pyroute2 package from master branch (release TBD....)
  
Prerequisites:
+
===DHCP Agent (usually part of the Network node)===
E_IPoIB port is configured and up
 
 
 
1. Make sure that eIPoIB module is up and configured in '''/etc/infiniband/openib.conf''': For more information, please refer to eIPoIB configuration in Mellanox OFED User Manual.
 
E_IPOIB_LOAD=yes
 
 
 
 
 
2. Restart openibd:
 
# service openibd restart
 
 
 
3. Modify the network bridge configuration according to the use of OpenVswitch or LinuxBridge
 
* 3.1 OpenVswitch '''/etc/neutron/plugins/ml2/openvswitch_agent.ini'''
 
[ovs]
 
bridge_mappings = default:br-<eIPoIB interface>
 
* 3.2 LinuxBridge file '''/etc/neutron/plugins/ml2/linuxbridge_agent.ini''':
 
[linux_bridge]
 
physical_interface_mappings = default:<eIPoIB interface>
 
 
 
 
 
NOTE: In order to obtain the eIPoIB interface name, run the ethtool tool command (see below) and check that driver name is eth_ipoib:
 
# ethtool -i <eIPoIB_interface>
 
driver: eth_ipoib
 
.....
 
 
 
 
 
4. Restart network bridge:
 
* 4.1 OpenVswitch
 
systemctl restart neutron-openvswitch-agent.service
 
* 4.2 LinuxBridge (if using linux bridge)
 
# service neutron-linuxbridge-agent restart
 
 
 
 
 
NOTE: For DHCP support, the Network node should use the Mellanox Dnsmasq driver as the DHCP driver.
 
 
 
===DHCP Server (Usually part of the Network node)===
 
  
 
1. Modify '''/etc/neutron/dhcp_agent.ini''' as follows and according to OVS or Linuxbridge:  
 
1. Modify '''/etc/neutron/dhcp_agent.ini''' as follows and according to OVS or Linuxbridge:  
Line 190: Line 157:
 
2. Restart DHCP server:  
 
2. Restart DHCP server:  
 
  # systemctl restart neutron-dhcp-agent.service
 
  # systemctl restart neutron-dhcp-agent.service
 +
 +
===L3 Agent (usually part of the Network node)===
  
 
==Compute Nodes==
 
==Compute Nodes==

Revision as of 15:09, 4 September 2019

Overview

Mellanox Neutron ML2 Driver

Mellanox ML2 Mechanism Driver implements the ML2 Plugin Mechanism Driver API. This driver supports Mellanox embedded switch functionality as part of the InfiniBand HCA. Mellanox ML2 Mechanism Driver provides functional parity with Mellanox Neutron plugin.

Mellanox ML2 Mechanism Driver supports DIRECT (pci passthrough) vnic type to allow VM network connectivity. For vnic type configuration API details, please refer to configuration reference guide. Hardware vNICs mapped to the guest VMs allow higher performance and advanced features such as RDMA (remote direct memory access).

The driver supports VLAN network type to facilitate virtual networks either on InfiniBand fabrics.

Prerequisites

  • CentOS 7.6 / Ubuntu 18.04 or later
  • Mellanox ConnectX® Family device:
   ConnectX®-3/ConnectX®-3 PRO 
   ConnectX®-4/ConnectX®-4Lx
   ConnectX®-5
   ConnectX®-6
  • Driver: Mellanox OFED 4.6-1.0.1.1 or greater
  • A running OpenStack environment installed (RDO Manager or Packstack).
  • SR-IOV enabled on all compute nodes.
  • The software package iproute2 installed on all Compute nodes
  • Mellanox UFM greater than 5.9.5

InfiniBand Network

An Infiniband network relies on a software entity to manage the network. This entity is referred to as a Subnet Manager or SM. Mellanox Neutron Plugin uses InfiniBand Partitions (PKeys) to separate Networks.

SM Node

OpenSM Provisioning with SDN Mechanism Driver

SDN Mechanism Driver allows OpenSM dynamically assign PKs in the IB network.

More details about applying SDN Mechanism Driver with NEO can be found here

Manual OpenSM Configuration

For ConnectX®-3/ConnectX®-3Pro use the following configuration

Change the following in /etc/opensm/opensm.conf:

  allow_both_pkeys TRUE

For ConnectX®-4 or newer use the following configuration

Change the following in /etc/opensm/opensm.conf:

virt_enabled 2

Partition membership configuration

In an Infiniband network, network segmentation is achieved through partitions (roughly equivalent to ETH VLAN). Each partition has its own key (15bit partition key). This file contains configuration of partition membership for all network endpoints in the system.

The following guidelines need to be followed to allow connectivity

For each PKEY its required to:

  1. Have OpenSM PF(physical function IB device) GUID be a member of the partition.
  2. Have L3 and DHCP PF GUID be a member of the partition.
  3. Have VF GUID be member of the partition (of the relevant VMs).


There is a 1:1 mapping between VLAN assigned to a network in openstack and the translation of that VLAN to PKEY (e.g VLAN 10 translates to PKEY 10)

Example1:

The following configurations corresponds to a single vlan network (vlan 3) with two VMs and a DHCP agent

management=0x7fff,ipoib, defmember=full : ALL, ALL_SWITCHES=full,SELF=full;
vlan3_vm1=0x3, indx0, ipoib, defmember=full : 0xfa163e0000c0851b;
vlan3_vm2=0x3, indx0, ipoib, defmember=full : 0xfa163e0000df0519;
vlan3_l3_dhcp_services=0x3, ipoib, defmember=full : 0xe41d2d030061f5fa;
vlan3_sm=0x3, ipoib, defmember=full : SELF;

Going over it line by line:

  1. make all member of the default (management) pkey
  2. VM1 port guid (VF) member of network with pkey 3
  3. VM2 port guid (VF) member of network with pkey 3
  4. L3/DHCP agent PF guid member of network with pkey3
  5. Subnet manager member of network with pkey3
Example 2:

The following configurations corresponds to a two vlan networks (vlan 3, vlan 5) with one VM on each network and a DHCP and L3 agent

management=0x7fff,ipoib, defmember=full : ALL, ALL_SWITCHES=full,SELF=full;
vlan3_vm1=0x3, indx0, ipoib, defmember=full : 0xfa163e0000c0851b;
vlan5_vm2=0x5, indx0, ipoib, defmember=full : 0xfa163e0000df0519;
vlan3_l3_dhcp_services=0x3, ipoib, defmember=full : 0xe41d2d030061f5fa;
vlan5_l3_dhcp_services=0x5, ipoib, defmember=full : 0xe41d2d030061f5fa;
vlan3_sm=0x3, ipoib, defmember=full : SELF;
vlan5_sm=0x5, ipoib, defmember=full : SELF;

Going over it line by line:

  1. make all member of the default (management) pkey
  2. VM1 port guid (VF) member of network with pkey 3
  3. VM2 port guid (VF) member of network with pkey 5
  4. L3/DHCP agent PF guid member of network with pkey3
  5. L3/DHCP agent PF guid member of network with pkey5
  6. Subnet manager member of network with pkey3
  7. Subnet manager member of network with pkey5

Restart the OpenSM:

After opensm.conf and partitions.conf have been updated, restart opensm service to load configurations

# systemctl restart opensmd.service

Controller Node

To configure the Controller node:

1. Install python-networking-mlnx package

Neutron Server

1. Make sure ML2 is the current Neutron plugin by checking the core_plugin parameter in /etc/neutron/neutron.conf:

core_plugin = neutron.plugins.ml2.plugin.Ml2Plugin

2. Make sure /etc/neutron/plugin.ini is pointing to /etc/neutron/plugins/ml2/ml2_conf.ini (symbolic link)

3. Modify /etc/neutron/plugins/ml2/ml2_conf.ini by adding the following:

[ml2]
type_drivers = vlan,flat
tenant_network_types = vlan
mechanism_drivers = mlnx_sdn_assist,mlnx_infiniband,openvswitch
# or mechanism_drivers = mlnx_sdn_assist,mlnx_infiniband,linuxbridge
[ml2_type_vlan]
network_vlan_ranges = default:1:10

4. Start (or restart) the Neutron server:

# systemctl restart neutron-server.service

Nova Scheduler

Enabling PciPassthroughFilter modify /etc/nova/nova.conf

 scheduler_available_filters = nova.scheduler.filters.all_filters
 scheduler_default_filters = RetryFilter, AvailabilityZoneFilter, RamFilter, ComputeFilter, ComputeCapabilitiesFilter, ImagePropertiesFilter, PciPassthroughFilter

Network Node

  1. Install python-networking-mlnx package and configure DHCP and L3 agents
  2. Install up to date pyroute2 package from master branch (release TBD....)

DHCP Agent (usually part of the Network node)

1. Modify /etc/neutron/dhcp_agent.ini as follows and according to OVS or Linuxbridge:

dhcp_driver = networking_mlnx.dhcp.mlnx_dhcp.MlnxDnsmasq
dhcp_broadcast_reply = True
1.1 For OVS
    interface_driver =  neutron.agent.linux.interface.OVSInterfaceDriver
1.2 For Linux Bridge
     interface_driver =  neutron.agent.linux.interface.BridgeInterfaceDriver


2. Restart DHCP server:

# systemctl restart neutron-dhcp-agent.service

L3 Agent (usually part of the Network node)

Compute Nodes

To configure the Compute Node:

1. Install Mellanox RPMs:

# yum install --nogpgcheck -y python-networking-mlnx

2. Create the file /etc/modprobe.d/mlx4_ib.conf and add the following:

options mlx4_ib sm_guid_assign=0

3. Restart the driver:

# /etc/init.d/openibd restart

Nova Compute

Nova-compute needs to know which PCI devices are allowed to be passed through to the VMs. Also for SRIOV PCI devices it needs to know to which physical network the VF belongs. This is done through the pci_passthrough_whitelist parameter under the default section in /etc/nova/nova.conf. For example if we want to whitelist and tag the VFs by their PCI address we would use the following setting: [pci] passthrough_whitelist = {"address":"*:0a:00.*","physical_network":"default"} This associates any VF with address that includes ':0a:00.' in its address to the physical network default.

1. add pci passthrough_whitelist to /etc/nova/nova.conf

2. Restart Nova:

# systemctl restart openstack-nova-compute

Neutron MLNX Agent

1. Run:

# systemctl enable neutron-mlnx-agent.service
# systemctl start neutron-mlnx-agent.service

2. Run:

# systemctl daemon-reload

3. In the file /etc/neutron/plugins/mlnx/mlnx_conf.ini, the parameters tenant_network_type , and network_vlan_ranges should be configured as the controllers:

physical_interface_mappings = default:<ib_interface>(for example default:ib0)

4. Modify the file /etc/neutron/plugins/ml2/eswitchd.conf as follows:

fabrics = default:<ib_interface> (for example default:ib0)

5. Start eSwitchd:

# systemctl enable eswitchd.service
# systemctl start  eswitchd.service

6. Start the Neutron agent:

# systemctl restart neutron-mlnx-agent

Known issues and Troubleshooting

For known issues and troubleshooting options refer to Mellanox OpenStack Troubleshooting

Issue: Missing zmq package on all nodes (Controller/Compute) Solution:

 # wget https://bootstrap.pypa.io/get-pip.py
 # sudo python get-pip.py
 # sudo pip install pyzmq