Difference between revisions of "Ironic/TripleO"
< Ironic
(updating) |
(→Using Ironic with TripleO: updated link to TripleO readme file) |
||
(3 intermediate revisions by 2 users not shown) | |||
Line 2: | Line 2: | ||
In this section, we will go over how to set up Ironic within the TripleO enviroment. | In this section, we will go over how to set up Ironic within the TripleO enviroment. | ||
− | : '''Note''': TripleO is under rapid development and may invalidate this walk | + | : '''Note''': TripleO is under rapid development and may invalidate this walk-through. |
If not familiar with TripleO and / or have not used the DiskImage-Builder (DIB) tool before, please read and familiarize yourself with the TripleO story. Here are some good starting points: | If not familiar with TripleO and / or have not used the DiskImage-Builder (DIB) tool before, please read and familiarize yourself with the TripleO story. Here are some good starting points: | ||
− | :* [https://github.com/openstack/tripleo-incubator/blob/master/README. | + | :* [https://github.com/openstack/tripleo-incubator/blob/master/README.rst TripleO-ReadMe] |
:* [http://docs.openstack.org/developer/tripleo-incubator/deploying.html Deploying-Doc] | :* [http://docs.openstack.org/developer/tripleo-incubator/deploying.html Deploying-Doc] | ||
:* [http://docs.openstack.org/developer/tripleo-incubator/devtest.html Devtest-Doc] | :* [http://docs.openstack.org/developer/tripleo-incubator/devtest.html Devtest-Doc] | ||
− | Check out | + | Check out tripleo-incubator master. |
− | |||
Switch the undercloud to build with Ironic by doing: | Switch the undercloud to build with Ironic by doing: | ||
Line 16: | Line 15: | ||
export USE_IRONIC=1 | export USE_IRONIC=1 | ||
− | Then, follow TripleO's [http://docs.openstack.org/developer/tripleo-incubator/devtest.html Devtest-Doc] | + | Then, follow TripleO's [http://docs.openstack.org/developer/tripleo-incubator/devtest.html Devtest-Doc]. |
− | + | After setup-baremetal is called in both the seed and undercloud stages you can use | |
+ | ironic node-list | ||
− | + | to list nodes and | |
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
ironic node-show $NODE | ironic node-show $NODE | ||
+ | to view nodes. | ||
You can now control the power state of this node with this command: | You can now control the power state of this node with this command: | ||
ironic node-set-power-state $NODE [on|off|reboot] | ironic node-set-power-state $NODE [on|off|reboot] |
Latest revision as of 12:24, 11 February 2015
Using Ironic with TripleO
In this section, we will go over how to set up Ironic within the TripleO enviroment.
- Note: TripleO is under rapid development and may invalidate this walk-through.
If not familiar with TripleO and / or have not used the DiskImage-Builder (DIB) tool before, please read and familiarize yourself with the TripleO story. Here are some good starting points:
Check out tripleo-incubator master.
Switch the undercloud to build with Ironic by doing:
export USE_IRONIC=1
Then, follow TripleO's Devtest-Doc.
After setup-baremetal is called in both the seed and undercloud stages you can use
ironic node-list
to list nodes and
ironic node-show $NODE
to view nodes.
You can now control the power state of this node with this command:
ironic node-set-power-state $NODE [on|off|reboot]