Difference between revisions of "GroupBasedPolicy/InstallCiscoACI"
Mike Cohen (talk | contribs) (→Installing and Running GBP with Cisco APIC) |
(→Devstack Installation) |
||
(4 intermediate revisions by 2 users not shown) | |||
Line 3: | Line 3: | ||
=== Devstack Installation === | === Devstack Installation === | ||
− | |||
− | 1. | + | 1. Follow the instructions here: https://github.com/group-policy/gbp-devstack/tree/juno until step 6. |
2. cd devstack | 2. cd devstack | ||
Line 11: | Line 10: | ||
3. Configure the local.conf file. | 3. Configure the local.conf file. | ||
+ | * Replace the "resource_mapping" driver with the "apic" driver as follows: | ||
+ | <pre> | ||
+ | [group_policy] | ||
+ | policy_drivers=implicit_policy,apic | ||
+ | </pre> | ||
+ | |||
+ | * Set the appropriate L3 plugin as follows in the default section: | ||
+ | <pre> | ||
+ | service_plugins =group_policy,servicechain,apic_gbp_l3 | ||
+ | </pre> | ||
+ | |||
+ | * Replace enable_service q-agt with disable_service q-agt | ||
* Set HOST_IP | * Set HOST_IP | ||
* Set Q_PLUGIN_EXTRA_CONF_PATH. This should point to the path where the ml2_conf_cisco.ini file resides. Note it should NOT start with a /. | * Set Q_PLUGIN_EXTRA_CONF_PATH. This should point to the path where the ml2_conf_cisco.ini file resides. Note it should NOT start with a /. | ||
Line 39: | Line 50: | ||
</pre> | </pre> | ||
− | 5. ./stack.sh | + | 5. pip install apicapi |
+ | |||
+ | 6. pip install python-opflex-agent | ||
+ | |||
+ | 7. ./stack.sh | ||
− | + | 8. Ensure your uplink to ACI fabric is up and a port is created on OVS. | |
<pre> | <pre> | ||
sudo ovs-vsctl add-port br-em1 eth1 | sudo ovs-vsctl add-port br-em1 eth1 | ||
</pre> | </pre> | ||
− | + | 8. source openrc demo demo | |
− | + | 9. Use the "gbp" CLI binary ("gbp --help" will give you the commands) |
Latest revision as of 00:28, 3 November 2015
Installing and Running GBP with Cisco APIC
The following are a set of instructions for installing and working with the Cisco APIC:
Devstack Installation
1. Follow the instructions here: https://github.com/group-policy/gbp-devstack/tree/juno until step 6.
2. cd devstack
3. Configure the local.conf file.
- Replace the "resource_mapping" driver with the "apic" driver as follows:
[group_policy] policy_drivers=implicit_policy,apic
- Set the appropriate L3 plugin as follows in the default section:
service_plugins =group_policy,servicechain,apic_gbp_l3
- Replace enable_service q-agt with disable_service q-agt
- Set HOST_IP
- Set Q_PLUGIN_EXTRA_CONF_PATH. This should point to the path where the ml2_conf_cisco.ini file resides. Note it should NOT start with a /.
4. Configure ml2_conf_cisco.ini at the path you chose. For complete instructions on available options see this document. An example file would look like this:
[DEFAULT] # Unique Name for identifying the Openstack Cluster apic_system_id=gbp3 [ml2_cisco_apic] # Host Name for the APIC Controller apic_hosts=172.31.100.1 # Username for the APIC Controller apic_username=admin # Password for the APIC Controller apic_password=cisco123 # How to map names to APIC: use_uuid or use_name apic_name_mapping=use_name # Switch to hypervisor port mapping [apic_switch:101] ubuntu-gbp=1/5
5. pip install apicapi
6. pip install python-opflex-agent
7. ./stack.sh
8. Ensure your uplink to ACI fabric is up and a port is created on OVS.
sudo ovs-vsctl add-port br-em1 eth1
8. source openrc demo demo
9. Use the "gbp" CLI binary ("gbp --help" will give you the commands)